Canon iR2022 Wartungshandbuch

Aug 8 2007Service ManualiR2030/2025/2022/2018 Series

Contents4.3.5.1 Outline...

Chapter 2 2-282.5.5 Registering the Card IDs0017-5553iR2022i / iR2025 / iR2030 / iR2018i1) Plug the power cord [1] into the outlet, and then turn on

Chapter 22-292.6 Installing the Heater PCB2.6.1 Preparing the parts0017-5554iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Prepare the follo

Chapter 2 2-302) Open the front cover [1].F-2-733) Remove the rear cover [1].- RS tightening screws (M3 x 8)[2], 4 pcs.4)Release the 3 hooks [1] and

Chapter 22-315) Remove the upper-right cover [1].- RS tightening screw (M3 x 8)[2], 1 pc.F-2-746) Remove the delivery tray [1].- RS tightening screws

Chapter 2 2-327) Using a nipper or the like, cut out the face plate [2] (used to install a heater switch) on the lower-right cover [1]. F-2-752.6.3 I

Chapter 22-333) Install the edge saddle [3]. Connect one heater switch harness [1] to the connector (J1901) on the heater PCB. Route the other harness

Chapter 2 2-345) Install the three clamps [1] on the back of the host machine.6) Connect the cassette heater harness [2] to the connector (J1905) on

Chapter 22-352.7 Installing the Reader Heater2.7.1 Preparing the parts0017-5557iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Prepare the fo

Chapter 2 2-362.7.2 Installing the Reader Heater Harness0017-5558iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Turn off the main power swi

Chapter 22-374) Remove the rear-left cover [2].- RS tightening screws (M3 x 8)[2], 1 pc.F-2-845) Open the core [1] on the rear side of the host machin

Contents6.2 Image Formation Process ...

Chapter 2 2-389) Turn over the reader flexible cable cover [1], and then secure to the back of the reader temporarily using a screw [2].F-2-86[1][2]

Chapter 22-3910) Pass the heater harness [1] though the harness guide [2] with the clamp [3] of the heater harness aligned with the notch [4] in the h

Chapter 2 2-4012) Secure the harness guide [1] to the rear bottom of the reader together with the heater harness [2].13) Connect the heater connector

Chapter 22-412.7.3 Removing Reader Components0017-5559iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Open the ADF/copyboard cover.2) Remove

Chapter 2 2-421) Remove the upper-left cover [1] of the reader.- Screws [2], 5 pcs.F-2-912) Remove the blind plate [1].- Screws [1], 2 cps.F-2-92b. M

Chapter 22-43F-2-943) Remove the jump board [2].- Screw [1], 1pc.F-2-954) Remove the stay [2].- Screws [1], 2pcs.F-2-962.7.5 Installing the Reader Hea

Chapter 2 2-441) Pull the front side [1] of the drive belt in the direction of the arrow to move the contact sensor [2] to the vicinity of center.F-2

Chapter 22-456) Attach the heater cover [1].- Screw [2], 1 pc.F-2-997) Install the reader heater [1].- Screw [2], 1 pc.8) Connect the connector [3] of

Chapter 2 2-4612) Install the copyboard glass.13) Install the right glass holder of the reader. - Screws, 2 pcs.14) Attach the rear-left cover of the

Chapter 22-472.8 Installing the Cassette Heater2.8.1 Preparing the parts0017-5562iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Prepare the

ContentsDelivery Sensor)...

Chapter 2 2-482.8.2 Installing the Cassette Heater0017-5563iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Turn off the main power switch [1

Chapter 22-494) From the rear of the host machine, insert the cassette heater [1] in the slot [2] in the host machine. 5) Secure the cassette heater [

Chapter 2 2-509) Remove the cassette rear cover [1].- Screws [2], 2 pcs.F-2-1069) Install the wire saddle (large) [2], lace the cassette heater harne

Chapter 22-512.9 Installing the Control Card Cable2.9.1 Preparing the parts0017-5564iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Prepare t

Chapter 2 2-522.9.2 Installing the Control Card Cable0017-5565iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Turn off the main power switch

Chapter 22-53

Chapter 3 Main Controller

ContentsContents3.1 Construction...

Contents8.3.1 Protective Functions...

Chapter 33-13.1 Construction3.1.1 Construction and Mechanisms0017-2274iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe machine's main co

Chapter 3 3-2F-3-2T-3-23.3 Image Processing3.3.1 Overview of the Image Flow0017-2384iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe followi

Chapter 33-3F-3-33.3.2 Construction of the Image Processing Module0017-2385iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe machine's ma

Chapter 3 3-4F-3-53.3.4 Compressio/ Extesion/ Editing Block0017-2387iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iHere, image data is proces

Chapter 33-5F-3-73.4 Flow of Image Data3.4.1 Flow of Image Data According to Copy Functions0017-2390iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2

Chapter 3 3-6F-3-93.4.3 Flow of Image Data for the Fax Transmission0017-2392iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe following is th

Chapter 33-7F-3-113.4.5 Flow of Image Data for the PDL Function0017-2394iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe following is the flo

Chapter 3 3-83.5 Parts Replacement Procedure3.5.1 Main Controller PCB3.5.1.1 Preparation for Removing the Image Processor PCB0017-2248iR2022i / iR202

Chapter 33-9F-3-17In the case of the capacitor PCB- 2 screws [3]F-3-187) Disconnect the USB memory [1].F-3-198) Free the relay cable [1] and disconnec

Contents9.4.10.2 Removing the Fan Filter (With Duplex Unit Type)...

Chapter 3 3-10F-3-2312) Detach the flexible cable guide [1].- 3 screws [2]F-3-2413) Detach the IP cover [1].- 15 screws [2]F-3-2514) Detach the image

Chapter 33-11F-3-273) Detach the RAM cover [1].- 5 screws [2]F-3-283.5.2.2 Removing the SDRAM0017-2252iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / i

Chapter 4 Original Exposure System

ContentsContents4.1 Construction...

Contents4.4.6.1 Removing the Contact Sensor HP Sensor...

Chapter 44-14.1 Construction4.1.1 Specifications, Control Methods, and Functions (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2022)0017-5566iR2022i / iR20

Chapter 4 4-24.1.3 Major Components (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2022)0017-5568iR2022i / iR2025 / iR2030 / iR2022Major components of the

Chapter 44-34.1.4 Major Components (iR2018i/iR2018)0017-6934iR2018 / iR2018iMajor components of the original exposure system are as follows:F-4-2T-4-

ContentsChapter 13 Correcting Faulty Images13.1 Making lnitial Checks ...

Chapter 4 4-4F-4-3[1] Printer main body (Connected to the image processor PCB)[2] Connected to ADF [3] Connected to the power supply PCB[4] Reader mo

Chapter 44-5[9] CISHP sensor (PS503)[10] Copyboard cover open/close sensor (Front: SR403)[11] Copyboard cover open/close sensor (Front: SR402)4.1.7 Re

Chapter 4 4-6F-4-6T-4-64.2 Basic Sequence4.2.1 Basic Sequence at Power-on0017-2623iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iJack No. Fun

Chapter 44-7F-4-7F-4-84.2.2 Basic Sequence after Depression of Start Key (Book mode, One Sheet of original)0017-2624iR2022i / iR2025 / iR2030 / iR2018

Chapter 4 4-8F-4-11F-4-124.3 Various Control4.3.1 Controlling the Scanner Drive System4.3.1.1 Outline0017-2626iR2022i / iR2025 / iR2030 / iR2018 / i

Chapter 44-94.3.1.2 Reader Motor Control0017-2627iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe reader motor driver controls rotation/stop

Chapter 4 4-10F-4-164.3.2.2 Analog Control Performed by the CIS (iR2022i/iR2022/iR2018i/iR2018)0017-2629iR2022i / iR2025 / iR2030 / iR2018 / iR2022

Chapter 44-114.3.2.3 Analog Control Performed by the CIS (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2022)0017-2630iR2022i / iR2025 / iR2030 / iR2022The

Chapter 4 4-12The original size is identified by the combination of presence and absence of output levels of the reflection type sensors as summarize

Chapter 44-132) The copyboard cover opens (at an angle of more than 30o). Original sensor: Turns off.F-4-213) The copyboard cover is closed (at an an

Contents15.3.1.1 Bit Switch Composition ...

Chapter 4 4-144.3.5 Dirt Sensor Control4.3.5.1 Outline0017-2635iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe machine changes the original

Chapter 44-15T-4-8F-4-284.3.6 Image Processing4.3.6.1 Outline0017-2636iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iMajor specifications and f

Chapter 4 4-16Functions of the image processing system are summarized below.T-4-10The reader controller PCB is used to process images on a line-by-li

Chapter 44-17The CMOS sensor outputs are necessary even for the following reasons even when the density of the original is uniform:(1) Variation in se

Chapter 4 4-184.4 Parts Replacement Procedure4.4.1 Copyboard glass4.4.1.1 Removing the Copyboard glass0017-8452iR2022i / iR2025 / iR2030 / iR2018 /

Chapter 44-194) Detach the right cover (Upper).5) Detach the left cover (rear).6) Open the copyboard cover (or ADF). 7) Detach the small cover.8) Disc

Chapter 4 4-2023) Remove the reader controller PCB [1] from the mount. - Screws [2], 3 pcs F-4-434.4.3 Scanner Motor4.4.3.1 Removing the Scanner Mot

Chapter 44-214) Detach the right cover (upper).5) Detach the left cover (rear).6) Open the copyboard cover (or ADF).7) Detach the small cover.8) Disco

Chapter 4 4-228) Remove the original sensor (vertical scan direction) [1]. - connector [2], 2 pcsF-4-534.4.7.2 Removing the Original Sensor (Horizon

Chapter 44-235) Remove the jump board [1]. - Screw [2], 1 pcsF-4-596) Remove the stream reading glass stay [1]. - Screw [2], 2 pcs7) Pull the drive

Contents15.4.7 <No.010 Frequency of the pseudo CI signal> ...

Chapter 5 Laser Exposure

ContentsContents5.1 Construction...

Chapter 55-15.1 Construction5.1.1 Overview0017-2643iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe laser scanner unit consists of a laser dr

Chapter 5 5-25.1.4 Control System Configuration0017-2648iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe laser exposure system is controlled

Chapter 55-3The following table shows combinations of laser control signals (CNTRL0, CNTRL1, and CNTRL2).T-5-35.2.1.2 Horizontal Synchronization Contr

Chapter 5 5-4From the moment the laser scanner motor starts to the moment it reaches the target revolution speed, the revolution speed is controlled

Chapter 55-5When the drum unit is drawn out, the interlocked laser shutter moves down, shutting off the laser beam path. When opening of the front cov

Contents15.7.2.4 <033: Top registration adjustment (duplex unit)>...

Chapter 5 5-65.3 Parts Replacement Procedure5.3.1 Laser Scanner Unit5.3.1.1 Removing the Laser Scanner Unit0017-8556iR2022i / iR2025 / iR2030 / iR201

Chapter 6 Image Formation

ContentsContents6.1 Construction...

Chapter 66-16.1 Construction6.1.1 Specifications of Image Formation System0017-4328iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-6-16.1.2 Ma

Chapter 6 6-2[2] Cleaner blade[3] Primary charging roller[4] Drum unit[5] Blade[6] Developing assembly[7] Toner bottle[8] Developing cylinder[9] Tran

Chapter 66-36.2 Image Formation Process6.2.1 Image Formation Process0017-4330iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe image formation

Chapter 6 6-4- During printingTo prevent fogging of the drum, the developing DC bias is held higher than usual except during image formation.To preve

Chapter 66-56.4 Driving and Controlling the High-Voltage System6.4.1 Outline0017-4333iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe voltage

Contents15.18.1 ROM Display...

Chapter 6 6-66.5.2 Charging Mechanism6.5.2.1 Primary Charging Bias Control0017-4335iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iWith the pri

Chapter 66-7A DC bias and an AC bias are applied to the developing cylinder. The ASIC on the DC controller PCB outputs the developing AC bias drive si

Chapter 6 6-8The transfer unit consists of a transfer roller [1] and an static eliminator [2]. The transfer roller is driven by the photosensitive dr

Chapter 66-96.9 Photosensitive Drum Cleaning6.9.1 Outline0017-4360iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iToner reaming on the photosens

Chapter 6 6-106.10 Parts Replacement Procedure6.10.1 Drum Unit6.10.1.1 Removing the Drum Unit0017-8557iR2022i / iR2025 / iR2030 / iR2018 / iR2022 /

Chapter 66-115) Select "#PRINT" using the + or - key, and then press the OK key. 6) Select "#PRINT SW" using the + or - key, and h

Chapter 7 Pickup/Feeding System

ContentsContents7.1 Construction...

Contents

Contents7.5.12.1 Removing the Registration Clutch...

Chapter 77-17.1 Construction7.1.1 Specifications/Configuration/Operation Methods0017-4363iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iFunctio

Chapter 7 7-27.1.2 Locations of Main Units0017-4364iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iLocations of main units of the pickup/feedin

Chapter 77-3[3] Feed roller 1[4] Multi pickup roller[5] Registration roller[6] Duplex paper feed roller 3[7] Transfer roller[8] Fixing roller[9] Duple

Chapter 7 7-47.1.6 Paper Path Drawing (Duplex Unit-B1/Finisher-U2)0017-4371iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iF-7-5[1] Cassette pi

Chapter 77-5F-7-7[1] Cassette pickup[2] Manual feed pickup [3] Delivery to copy tray 1[4] Delivery to copy tray 2 (option *1)[5] Duplex paper feed ass

Chapter 7 7-6F-7-9[1] Cassette 1 paper presence/absence sensor (SR204)[2] Registration sensor (SR209) [3] Manual feed paper presence/absence sensor (

Chapter 77-7T-7-47.2.2 Stationary Jams7.2.2.1 Stationary Jam in Pickup Assembly0017-4383iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iStationa

Chapter 7 7-8F-7-107.3.2 Cassette Pickup Operation0017-4387iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iRotation of the pickup roller is con

Chapter 77-94) When the pickup roller rotates once, the toothless portion of the pickup roller drive gear comes to the position of the relay gear and

Chapter 1 Introduction

Chapter 7 7-107.4 Manual Feed Pickup Unit7.4.1 Overview0017-5466iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018ia. Multi Manual feed Pickup Con

Chapter 77-117.5 Parts Replacement Procedure7.5.1 Pickup Roller7.5.1.1 Removing the Cassette Paper Pickup Roller0017-8563iR2022i / iR2025 / iR2030 / i

Chapter 7 7-127) Detach ground wire [1] from harness guide [2].- Screw [3], 1 pc.F-7-238) Detach ground wire [1] from wire saddle [2] and harness gui

Chapter 77-131) Remove the retry sensor [1].- Connector [2], 1 pc.F-7-277.5.6 Cassette Paper Sensor7.5.6.1 Removing the Cassette Paper Presence/Absenc

Chapter 7 7-146) Remove the multi-paper roller [1].- Bearing [1], 1 pc.F-7-327.5.9 Manual Feed Tray paper sensor7.5.9.1 Removing the Multifeeder Pape

Chapter 77-155) Remove the feed guide [1].- Screw [2], 2 pcs.F-7-376) Detach the multifeeder connector cover [1].- Connector [2], 3 pcs.F-7-387) Remo

Chapter 7 7-162) Disconnect the connector [1], and then remove the harness from the threewire saddles [2].3) Remove the resin ring [3], and then remo

Chapter 8 Fixing System

ContentsContents8.1 Construction...

Chapter 88-18.1 Construction8.1.1 Specifications, Control Mechanisms and Functions0017-5468iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-8-1

Chapter 8 8-2F-8-28.2 Various Control Mechanisms8.2.1 Controlling the Speed of the Fixing Film8.2.1.1 Controlling the Fixing Film Speed0017-5470iR202

Chapter 88-3The CPU on the DC controller monitors the voltage of the M_TH/S_TH signal to control the fixing heater 1 drive signal (H1DRV) and fixing h

Chapter 8 8-4This machine controls the fixing temperature according to the "media type" selected in the user mode and the "target temp

Chapter 88-58.2.2.6 Target Temperatures by Mode (iR2018/iR2018i/iR2018N)0018-0280iR2018 / iR2018iThis machine controls the fixing temperature accordi

Chapter 8 8-6F-8-5Protection FunctionsThis machine is provided with the following four protection functions to prevent the fixing heater from overhea

Chapter 88-7Fixing System Error CodesE000-0000 STARTUP ERRORThe temperature detected by the main and sub thermistors did not reach the prescribed temp

Chapter 8 8-88.4 Parts Replacement Procedure8.4.1 Fixing Unit8.4.1.1 Removing the Fixing Unit0017-8159iR2022i / iR2025 / iR2030 / iR2018 / iR2022 /

Chapter 88-99) Detach the heater harness cover [2]. Disconnect the connector [3].- Screw [1], 1 pc. F-8-1110) Disconnect the two connectors [1], and t

ContentsContents1.1 System Construction ...

Chapter 8 8-102) Remove the fixing pressure release lever [2].- Resin ring [1]F-8-17When installing the fixing pressure release lever, check that the

Chapter 88-117) Remove the ground cable [1] from the holder, and then free the fixing unitAC harness. F-8-248) Remove the roller guide unit [1].- Scre

Chapter 8 8-128.4.4 Fixing Delivery Sensor8.4.4.1 Removing the Fixing Delivery Sensor0017-8168iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1

Chapter 88-13When installing the electrode plate [1], place it under the three claws [2] asshown below.F-8-358.4.5 Fixing Film Sensor8.4.5.1 Removing

Chapter 9 External and Controls

ContentsContents9.1 Control Panel...

Contents9.4.11.1 Removing the Main Motor ...

Chapter 99-19.1 Control Panel9.1.1 Overview (iR2022/iR2022N/iR2018/iR2018N)0017-5478iR2018 / iR2022The machine's control panel consists of the f

Contents1.2.7.2 Printing Speed (iR2025/iR2025i) ...

Chapter 9 9-2This machine is provided with a fan to cool the fixing unit.F-9-39.2.2 Overview (iR2030i/iR2030/iR2025i/iR2025/iR2022K/iR2022i/iR2018i)0

Chapter 99-3When the CPU on the engine controller outputs a fan half speed signal (FAN_HALF), the fan drive voltage switching circuit supplies a +16 V

Chapter 9 9-4F-9-79.3.1.2 Rated Output of the Power Supply PCB0017-9316iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i9.3.2 Protection Functio

Chapter 99-59.4 Parts Replacement Procedure9.4.1 External Covers9.4.1.1 External Covers9.4.1.1.1 Removing the Lower-left Cover0017-8590iR2022i / iR202

Chapter 9 9-6F-9-139.4.1.7 Reader Front Cover9.4.1.7.1 Removing the Reader Front Cover0017-8622iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Chapter 99-79) Remove the gear unit [1] and gear [2].- E-ring [3], 1 pc. F-9-1810) Pull out the handle [1] at the back of the machine, remove the scre

Chapter 9 9-814) Remove the main drive unit [1].- Screw [2], 6 pcs.F-9-239.4.3 Fixing Drive Assembly9.4.3.1 Removing the Fixing Drive Unit0017-8653iR

Chapter 99-94) Remove the power supply PCB [1].- Connector [2], 7 pcs. - Screw [3], 6 pcs.F-9-27F-9-289.4.5 Control Panel9.4.5.1 Removing the Operatio

Chapter 9 9-103) Disconnect the flexible cable holder [1] and disconnect the connector [3]of the flexible cable [2] to remove the operation panel un

Chapter 99-111) Open the left door until it stops.2) Remove the transfer/registration unit [1].- Screw [2], 4 pcs.F-9-373) Disconnect the connector [1

Chapter 11-11.1 System Construction1.1.1 Pickup/Delivery/Original Handling Accessories System Configuration (iR2018)0017-9181iR2018 The configuration

Chapter 9 9-124) Disconnect the relay harness [2] from the connector [1].5) Disconnect the ground cable [3].- Screw [4], 1 pc. 6) Remove the reusable

Chapter 99-131) Open the left door until it stops.2) Remove the transfer/registration unit [1].- Screw [2], 4 pcs. F-9-463) Disconnect the connector [

Chapter 9 9-148) Remove the duplex unit [1] from the left door.- Screw [2], 6 pcs. F-9-529) Remove the fan filter from the duplex unit.9.4.11 Motor o

Chapter 99-152) Open the left door until it sops and pull out the hinge shaft [1].F-9-563) Lift the left door with both hands to release it from the d

2) Open the left door until it sops and pull out the hinge shaft [1].F-9-603) Lift the left door with both hands to release it from the door rotation

Chapter 10 RDS

ContentsContents10.1 RDS...

Chapter 1010-110.1 RDS10.1.1 Overview0017-6733iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iProduct OverviewEmbedded RDS (henceforth: e-RDS) i

Chapter 1 1-21.1.2 Pickup/Delivery/Original Handling Accessories System Configuration (iR2018i)0017-9182iR2018iThe configuration is as shown in the f

Chapter 10 10-2(As for deletion of certificate, see 'CA certificate'.)10.1.7 SOAP Communication Function0017-6740iR2022i / iR2025 / iR2030

Chapter 1010-3- The timing of transmission to UGW varies according to the device.- The timing of transmission to UGW cannot be set on the side of the

Chapter 10 10-4An example for the transition of the menu related to the e-RDS in the service mode.F-10-1(3). Communication Error Log Selection Screen

Chapter 1010-510.1.12 Alarm Filtering, Alert Filtering0017-6745iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iWith the instruction from UGW (ge

Chapter 10 10-6#CLEAR > ERDS-DATIf necessary, install or delete CA Certificate and turn off/on the power.(1)-3. Display the menu screen of e-RDSPr

Chapter 1010-76 Proxy connection error Proxy connection error Cannot connect to the Proxy server. Check the server IP address and port number and cor

Chapter 10 10-8[Method Name]:T-10-417 Server response time out Server response time out Due to network congestion etc., response from server does no

Chapter 1010-9[Detail of server error]:Display detailed error information from error in case there is an error response from UGW. However, in case the

Chapter 11 Maintenance and Inspection

Chapter 11-31.1.3 Pickup/ Delivery /Original Handling Accessories System Configuration (iR2022/iR2022N/iR2025/iR2030)0017-9183iR2025 / iR2030 / iR2022

ContentsContents11.1 Periodically Replaced Parts ...

Chapter 1111-111.1 Periodically Replaced Parts11.1.1 Overview0017-5958iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe machine has parts that

Chapter 11 11-2F-11-111.3 Scheduled Servicing Basic Procedure11.3.1 Scheduled Servicing0017-5969iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018

Chapter 12 Standards and Adjustments

ContentsContents12.1 Scanning System...

Chapter 1212-112.1 Scanning System12.1.1 Procedure after Replacing the CIS (LCD type)0017-5978iR2018 / iR2022After replacing the contact image sensor

Chapter 1 1-41.1.4 Pickup/Delivery/Original Handling Accessories System Configuration (iR2022i/iR2022K/iR2025i/iR2030i)0017-9187iR2022i / iR2025 / iR

Chapter 12 12-2- Read position adjustment (Stream reading: Only when the ADF is installed)1) Enter the service mode.Sequentially press the Additional

Chapter 1212-3

Chapter 13 Correcting Faulty Images

ContentsContents13.1 Making lnitial Checks ...

Chapter 1313-113.1 Making lnitial Checks13.1.1 Site Environment0017-5987iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018ia. There must be a sourc

Chapter 13 13-2- Check the power cables and signal cables of options are connected properly.- Check whether no fuse on PCBs is blown. - Check whether

Chapter 1313-313.2.2 Motor13.2.2.1 List of Motors0017-5996iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i<Reader Unit>F-13-2Symbol Name F

Chapter 11-51.1.5 Reader Heater/Cassette Heater System Configuration (iR2018/iR2022/iR2022N)0017-9191iR2018 / iR2022The configuration is as shown in

Chapter 13 13-4<Printer Unit>F-13-313.2.3 Fan13.2.3.1 List of Fans0017-5997iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iSymbol Name Fu

Chapter 1313-5<Reader Unit>The reader unit has no fan.<Printer Unit>T-13-1F-13-413.2.4 Sensor13.2.4.1 List of Sensors0017-5998iR2022i / iR

Chapter 13 13-6<Reader Unit>T-13-2T-13-3F-13-5Symbol Name FunctionSR401 CIS HP sensor Detects the CIS home position.SR402 Copyboard cover open/

Chapter 1313-7<Printer Unit>T-13-4Symbol Name FunctionSR101Fixing film speed sensor Detects the fixing film speed.SR202Fixing delivery sensor De

Chapter 13 13-8T-13-5T-13-6F-13-613.2.5 Switch13.2.5.1 List of Switches0017-5999iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iSymbol Part No.

Chapter 1313-9<Reader Unit>The reader unit has no switch. <Printer Unit>F-13-713.2.6 Lamps, Heaters, and Others13.2.6.1 List of Lamps, Hea

Chapter 13 13-10<Reader Unit>F-13-8<Printer unit>Symbol Name Part No. FunctionH3 Reader heater (left) NPNPrevents dew condensation on the

Chapter 1313-11F-13-913.2.7 PCBs13.2.7.1 List of PCBs0017-6001iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iSymbol Part No.H1,H2Fixing film un

Chapter 13 13-12<Reader Unit>F-13-10<Printer unit>Symbol Name Part No. Function[1]Reader controller PCB FM2-4792 controls the reader unit

F-13-11F-13-12[1][2][3][4][5][6][7][8][9][10][11][12][13][14][15][16][17]

ApplicationThis manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repairof products

Chapter 1 1-61.1.6 Reader Heater/Cassette Heater System Configuration (iR2018i)0017-9193iR2018iThe configuration is as shown in the following figure:

Chapter 14 Self Diagnosis

ContentsContents14.1 Error Code Table...

Chapter 1414-114.1 Error Code Table14.1.1 List of Error Codes0017-6036iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-1Error Code Detail Co

Chapter 14 14-214.2 Error Code Details14.2.1 Error Code Details0017-6037iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-2Display CodeDetai

Chapter 1414-3E197 0000 Printer engine communication error Erroneous communication between the DC controller PCB and image processor PCB was detected.

Chapter 14 14-4E808 0000 Fixing drive circuit failure- The heater does not turn on.- A fixing drive motor failure was detected. - Check the connector

Chapter 1414-514.3 Jam Code14.3.1 Jam Codes (Related to Printer Unit)0017-6038iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-314.3.2 Jam C

Chapter 11-71.1.7 Reader Heater/Cassette Heater System Configuration (iR2022K/iR2022i/iR2025/iR2025i/iR2030/iR2030i)0017-9194iR2022i / iR2025 / iR2030

Chapter 14 14-6T-14-614.3.5 Jam Codes (Related to Inner 2-way Tray)0017-6042iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-7Code Name Sen

Chapter 1414-714.4 Finisher Error Codes14.4.1 Error Code Details0017-6043iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-8Display codeDetai

Chapter 14 14-8E540 0001 - Standard tray shift motor or finisher controller PCB failure- Standard tray HP sensor failure- Standard tray clock sensor

Chapter 1414-9E542 0001 - Optional tray motor or finisher controller PCB failure- Optional tray HP sensor failure- Optional tray clock sensor failure-

Chapter 14 14-1014.5 FAX Error Codes14.5.1 Outline14.5.1.1 Error Code Outline0017-6044iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iAn error

Chapter 1414-11##0282 [Tx] at time of transmission, the procedural signal has been transmitted more than specified.##0283 [Tx] at time of transmissio

Chapter 14 14-12##0793 [Rx] at time of ECM reception, no effective frame is received while high-speed signal reception is under way, thus causing ti

Chapter 15 Service Mode

ContentsContents15.1 Outline...

Chapter 1 1-81.1.8 Printing/Transmitting Accessories System Configuration (iR2018/ir2022/iR2022N)0017-9196iR2018 / iR2022The configuration is as sho

Contents15.3.12.2 Detailed Discussions of Bit 0...

Contents15.6.21 <197: Shading Target Value (Green)> ...

Contents15.8.1 Confirmation of contents of CA certificate ...

Chapter 1515-115.1 Outline15.1.1 Outline of Service Mode0017-8503iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe items that follow may be ch

Chapter 15 15-2Displays ROM information, such as version numbers and checksums.#TEST MODEMakes various status checks, such as contact sensor, sensor

Chapter 1515-3F-15-215.2 Default settings15.2.1 Service Mode Menus0017-6051iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i#SSSWNo. Initial sett

Chapter 15 15-4#MENUNo. Initial setting Range ofsettingFunction01: - 04: not used05: 0 ON/OFF NL equalizer setting06: 0 0: DIAL1: SERVICEMAN [1]2: SE

Chapter 1515-5062: - 080: not used#SPECIAL Do not change.#NCU Do not change.#FAX Not used.#SCANNo. Initial setting Range setting Explanation#SCAN SW S

Chapter 15 15-6#SCAN NUMERIC001: - 023: Not used024: 385 300 to 450, one unit=0.1mmCIS scan position during ADF scanning. 026: 22 6 to 48, one unit=0

Chapter 1515-7#PRINTNo. Initial setting Range setting Explanation#PRINT SW SW01 - SW04 Not usedSW05 10000000 Horizontal scanning priority recordSW06 -

Chapter 11-91.1.9 Printing/Transmitting Accessories System Configuration (iR2018i/iR2022i/iR2022K/iR2025/iR2025i/iR2030/iR2030i)0017-9197iR2022i / iR2

Chapter 15 15-8#PRINT CST U1 0 0: G_LTR Paper size group U1 special, standard-size paper entry29: A-LTR31: G-LTR40: 8KU2 0 0: FLSP Paper size group U

Chapter 1515-9ERACE Not used#REPORTSetting Function#REPORT SW Not used#REPORT OUTPUT SERVICE DATA LIST Output of service data listSYSTEM DATA LIST Out

Chapter 15 15-1015.3 Setting of Bit Switch (SSSW)15.3.1 Outline15.3.1.1 Bit Switch Composition0017-6052iR2022i / iR2025 / iR2030 / iR2018 / iR2022 /

Chapter 1515-1115.3.3 SSSW-SW0315.3.3.1 List of Functions0017-6055iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-15-215.3.3.2 Detailed Discus

Chapter 15 15-12Use it to select an appropriate reception mode after transmission of the CFR signal.If errors occur frequently at time of reception b

Chapter 1515-13T-15-5The machine will stop the ongoing communication if the transmission/reception of a single original page takes 32 min or more. To

Chapter 15 15-1415.3.7.2 Detailed Discussions of Bit 20017-6070iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iIt converts "inch" int

Chapter 1515-1515.3.9.2 Detailed Discussions of Bit 00017-8528iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iTransmitted telephone number could

Chapter 15 15-1615.3.11 SSSW-SW3015.3.11.1 List of Functions0017-6081iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-15-1315.3.11.2 Detailed

Chapter 1515-17Use it to specify whether B4 paper (Scan) should be counted as large-size paper.If 'yes' is selected, B4 paper will be counte

Chapter 1 1-101.1.10 Functions of the Printing/Transmission Functions (iR2018/iR2022/iR2022N)0017-5905iR2018 / iR2022The following is a brief explan

Chapter 15 15-1815.4.2 <No.005 NL equalizer>0017-6093iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iUse it to enable-disable the NL equa

Chapter 1515-1915.5.2 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition (3)>

Chapter 15 15-2015.5.8 <016: time length to first response at time of fax/tel switchover>0017-6108iR2022i / iR2025 / iR2030 / iR2018 / iR2022

Chapter 1515-21Serial No. on counter check screenCounter type Print systemBk 1-sided L Bk 1-sided S Bk 2-sided L Bk 2-sided SLocal copyPDL printFAX pr

Chapter 15 15-22266 CopyA (Bk/S/2-sided) 1277 Local copy(Bk1) 1 1278 Local copy(Bk2) 2 1283 Local copy(Bk/L) 1284 Local copy(Bk/S) 1293 Local copy(Bk

Chapter 1515-2315.6 Setting of Scanner Functions (SCANNER)15.6.1 Setting of Bit Switch0017-6116iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i&

Chapter 15 15-24Specify whether to output an image for ADF perpendicularity adjustment.15.6.2 Numeric Parameter Functional configuration0017-6117iR20

Chapter 1515-25If any operation error occurs after changing the setting value, change the setting value to the original one.15.6.3 <024:CIS scan po

Chapter 15 15-2615.6.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)>0017-6124iR2022i / iR2025 / iR2

Chapter 1515-275: A_LTR_R15.6.20 <196: Shading Target Value (Red)>0017-6135iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThis is market-

Chapter 11-11F-1-101.2.1.2 External View (iR2020/iR2020N/iR2030/iR2025)0017-6950iR2025 / iR2030 / iR2022F-1-11*1: This accessory comes standard with t

Chapter 15 15-2815.7 Setting of Printer Functions (PRINTER)15.7.1 Service Soft Switch Settings (PRINTER)15.7.1.1 SSSW-SW0515.7.1.1.1 List of Function

Chapter 1515-2915.7.1.2.2 Detailed Discussions of Bit 00017-6144iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iSelect whether to enable or disa

Chapter 15 15-3015.7.1.3.2 Detailed Discussions of Bit 00017-6153iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iSelect whether to inhibit auto

Chapter 1515-3115.7.1.4.4 Detailed Discussions of Bit 20017-8536iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iWhen selecting the post cards, b

Chapter 15 15-3215.7.2.6 <035: Left-end registration adjustment (cassette 1)>0017-6162iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iAdj

Chapter 1515-3315.7.2.21 <061:Adjustment of the registration loop volume. (Duplex unit)>0017-8648iR2022i / iR2025 / iR2030 / iR2018 / iR2022 /

Chapter 15 15-3415.8 Network Parameter Settings (NETWORK)15.8.1 Confirmation of contents of CA certificate0017-6175iR2022i / iR2025 / iR2030 / iR2018

Chapter 1515-3515.11 License Management (LMS)15.11.1 Outline0017-8537iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iLMS (License Management Ser

Chapter 15 15-36BIT 05: BW-SEND -> SENDBIT 06: CL-SEND -> SENDBIT 09: BDL-IMAGE( 600) -> CARPS215.11.3 Inactivity of the tra

Chapter 1515-37Settings related to e-RDS are described below.T-15-2715.13 Display of Counter Information (COUNTER)15.13.1 Counters0017-6180iR2022i / i

Chapter 1 1-12F-1-121.2.1.4 External View (iR2018)0017-5917iR2018 F-1-13*1: This accessory comes standard with the models for Asia and the models for

Chapter 15 15-38T-15-2915.13.2 Clearing Counters0017-6181iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i- Maintenance/parts counter all clearE

Chapter 1515-39F-15-915.14.3 System Dump List0017-6187iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i- System Dump ListUse it to check the hist

Chapter 15 15-40*7: Total number of pages transmitted and received in each mode*8: Total number of pages printed/scanned*9: Total number of occurrenc

Chapter 1515-41F-15-12Jam history description (JAM)Item Explanation[1] Number The larger the number of a jam, the more recently it has occurred.[2] Ja

Chapter 15 15-4215.14.6 Spec List0017-6190iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i[7] Jam code Code Jam causeHost machine 0104 Pickup a

Chapter 1515-43F-15-13******************************** SPEC REPORT ********************************07/12/2005 13:07 FAX 001TYPELBP SPEEDTOTAL MEMO

Chapter 15 15-44F-15-14[1] Type setting[2] Print speed[3] Memory size[4] ROM version (MAIN/BOOT/LANG*1(language liblary/language file version)ECONT/o

Chapter 1515-4515.14.7 Service Label0017-6191iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iEnter the value given in the service label affixed

Chapter 15 15-4615.15 Download (DOWNLOAD)15.15.1 Download0017-6182iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe following parts of this u

Chapter 1515-4715.17 Error Display (ERROR DISPLAY)15.17.1 Error Display0017-8542iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iAn error code is

Chapter 11-13F-1-141.2.2 Using the Machine1.2.2.1 Turning On the Power Switch (iR2018/iR2022/iR2022N)0017-5920iR2018 / iR2022[1] CIS unit [10] Separa

Chapter 15 15-48(1) SHADING Automatic gain adjustment(3) SHEET POS ADJ CS position adjustment(4) TRASH DETECT Dust detection(5), (6), (9), (*) Not us

Chapter 1515-4915.19.3 Test Mode Menu List (Touch Panel Type)0017-6195iR2022i / iR2018iTest mode menu listTo invoke test mode, follow these steps:1) E

Chapter 15 15-50(1) RELAY TEST [1] - [2](1) RELAY TEST 1 NCU relay (and switch) ON/OFF test(2) RELAY TEST 2 230 V common NCU test(2) FREQ TEST [0] -

Chapter 1515-5115.19.4 D-RAM Test<(1) D-RAM TEST>0017-6196iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iD-RAM Test((1) D-RAM)Press the n

Chapter 15 15-5215.19.5 Scan Test ((2) SCAN TEST)0017-6197iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iScan test ((2) SCAN TEST)Press the nu

Chapter 1515-53Press '1'or '2' on the keypad on the Modem test menu to select relay test mode. Use the keypad to operate the vario

Chapter 15 15-54MEMO:The output level of individual signals is in keeping with the setting made in service mode.DTMF Signal Transmission TestA press

Chapter 1515-5515.19.8 Function Test ((6) FUNCTION TEST)0017-6203iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iFunction test ((6) FUNCTION TES

Chapter 15 15-56F-15-226-3:SENOR[1] - [6]SENSOR CHECK0:NORMAL 1:LATCHSWITCH CHECK[0] - [1]DS ON DES of HPS ONBCVS ofPress numeric keypad key 1.SENSOR

Chapter 1515-57F-15-23ADF feed test (6-4: ADF FEED TEST)ADF operation verification mode. Press numeric keypad key 4 on the FUNCTION TEST menu to sele

Chapter 1 1-14The machine possesses 2 power switches: main power switch and control power switch. Normally (i.e., unless the machine is in a sleep st

Chapter 15 15-58F-15-24Lamp test (6-8: LAMP TEST)Press numeric keypad key 8 on the FACULTY menu to select the scan lamp illumination mode. The test

Chapter 16 Upgrading

ContentsContents16.1 Outline...

Chapter 1616-116.1 Outline16.1.1 Overview of Upgrade (LCD type)0017-6002iR2018 / iR2022This machine and options can be upgraded by downloading system

Chapter 16 16-216.1.3 Overview of Service Support Tool (LCD type)0017-6005iR2018 / iR2022F-16-1When using the SST, select "#DOWNLOAD" in t

Chapter 1616-3F-16-2When using the SST, select "#DOWNLOAD" in the service mode to place the main unit in the download mode. (The finisher ne

Chapter 16 16-44) Click the "Register Firmware" button. F-16-35) Select the drive in which the system CD is inserted, and then click the &

Chapter 1616-56) A list of system software programs contained in the system CD is displayed. Uncheck the checkboxes of unnecessary folders and system

Chapter 11-15The machine possesses 2 power switches: main power switch and control power switch. Normally (i.e., unless the machine is in a sleep stat

Chapter 16 16-63) Start SST.4) Click the "Register Firmware" button. F-16-75) Select the drive in which the system CD is inserted, and the

Chapter 1616-76) A list of system software programs contained in the system CD is displayed. Uncheck the checkboxes of unnecessary folders and system

Chapter 16 16-81) Turn off the main power switch of this machine, and then disconnect the cables connected to this machine.2) Connect USB connector o

Chapter 1616-94) Double-click the "System" folder in "Model List" to check the system software version. Select "USB" in

Chapter 16 16-1010) When connection is complete, the following screen appears. Click the OK button.F-16-1611) Click "System Software Download&qu

Chapter 1616-1112) Select the version of the system software to download from the list. Check that the selected version is displayed in "Selected

Chapter 16 16-1214) While the received data is being written to the flash ROM after completion of downloading, the following screen is displayed:F-16

Chapter 1616-1316) When the Selecting a Job screen appears, click "Return to Main Menu".F-16-2217) Click the "OK" button to return

Chapter 16 16-1418) Click the "EXIT" button to terminate SST.F-16-2419) Confirm the massage "ROM WRITE OK" indicated on the contr

Chapter 1616-154) Double-click the "System" folder in "Model List" to check the system software version. Select "USB" in

IntroductionSymbols UsedThis documentation uses the following symbols to indicate special information:Symbol DescriptionIndicates an item of a non-spe

Chapter 1 1-16<During printing or fax data transmission/reception>Be sure to operate the main power switch while the Processing/Data lamp on th

Chapter 16 16-1610) When connection is complete, the following screen appears. Click the OK button.F-16-2911) Click "System Software Download&qu

Chapter 1616-1712) Select the version of the system software to download from the list. Check that the selected version is displayed in "Selected

Chapter 16 16-1814) While the received data is being written to the flash ROM after completion of downloading, the following screen is displayed:F-16

Chapter 1616-1916) When the Selecting a Job screen appears, click "Return to Main Menu".F-16-3517) Click the "OK" button to return

Chapter 16 16-2018) If the other firmware is upgraded continuously, follow each downloading procedure. If the downloading is finished, click the &quo

Chapter 1616-21To download the software for 32MB ROM PCB of the extension slot, use the steps given for the system software.When selecting a download

Chapter 16 16-223) Select "MFP" in "Target Selection", and then select "iR2018i" in "Model List".F-16-404) Do

Chapter 1616-237) Using or , select "#DOWNLOAD". 8) Press the OK key on the control panel to place the host machine in the downloading w

Chapter 16 16-2411) Click "CA_KET Download" on the Selecting a Job screen.F-16-4412) Select the version of the system software to download

Chapter 1616-2513) When downloading starts, the progress of downloading is displayed by the progress bar.F-16-46Never turn off the power switch of the

Chapter 11-171.2.2.4 When Turning Off the Main Power Switch (iR2018i/iR2022i/iR2022K/iR2025/iR2025i/iR2030/iR2030i)0017-5923iR2022i / iR2025 / iR2030

Chapter 16 16-2615) When the Selecting a Job screen appears, click "Return to Main Menu".F-16-4816) Click the "OK" button to retu

Chapter 17 Service Tools

ContentsContents17.1 Service Tools...

Chapter 1717-117.1 Service Tools17.1.1 Special Tools0017-6022iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iIn addition to the standard tools s

Chapter 17 17-2Lubricant drive mechanism, sliding mechanism, scanner railsilicone oil - CK-0551 (20 g)Lubricant (EM-50L)gear special oilspecial solid

Aug 8 2007

Chapter 1 1-181.2.2.5 Control Panel0017-5926iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iF-1-211.2.3 User Mode Items1.2.3.1 Common Settings

Chapter 11-19*1 Indicates the default setting. *2 Indicates items that appear only when the appropriate optional equipment is attached. 1.2.3.2 Timer

Chapter 1 1-20T-1-4*1 Indicates the default setting. 1.2.3.5 System Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)0017-5942iR2022i / iR2025

Chapter 11-21*1 Indicates the default setting. *2 Indicates items that appear only when the appropriate optional equipment is attached. 1.2.3.6 Copy S

Chapter 1 1-22*1 Indicates the default setting. *2 Indicates items that appear only when the appropriate optional equipment is attached. 1.2.3.8 Prin

Chapter 11-23*1 Rotate items do not appear when the optional Finisher-U2 is attached. *2 Offset and staple items appear only when the optional Finishe

Chapter 1 1-241.2.4.2 Cleaning (LCD type)0017-5953iR2018 / iR2022The parts that should be cleaned by the customer to maintain the design performance

Chapter 11-257) Place the cleaning pattern printed in step 5 in the manual feed tray with "V" up.F-1-258) Using the left and right arrow key

IntroductionThe following rules apply throughout this Service Manual:1. Each chapter contains sections explaining the purpose of specific functions an

Chapter 1 1-261) Press the Additional functions key to enter the user mode.2) Select "Adjustment/Cleaning" on the touch panel.3) Select &qu

Chapter 11-271.2.5.3 Handling the Laser Unit 0017-2610iR2018 / iR2022The laser scanner unit emits invisible laser light inside it. If exposed to lase

Chapter 1 1-28F-1-321.2.5.5 Safety of Toner0017-2612iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iThe machine's toner is a non-toxic mat

Chapter 11-291.2.6 Product Specifications1.2.6.1 Product Specifications0017-2617iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iCopyboard stream

Chapter 1 1-301.2.7 Function List1.2.7.1 Printing Speed (iR2030/iR2030i)0017-5909iR2030Power consumption Average power consumption120V model: 646 W o

Chapter 11-31Paper size Single-sided Double-sidedCasette feed Manual feed Casette feed Manual feedPlain paper A4 30 30 27.5 27.5A5 25.5 25.5 - -A5R -

Chapter 1 1-32*1. Bond SP. FIX. Mode in the user mode: OFF*2. Bond SP. FIX. Mode in the user mode: ONSupplement:- The above copy speed does not chang

Chapter 11-33

Chapter 1 1-34T-1-10Paper size Single-sided Double-sidedCasette feed Manual feed Casette feed Manual feedPlain paper A4 25 25 23.5 23.5A5 25.5 25.5 -

Chapter 11-35*1. Bond SP. FIX. Mode in the user mode: OFF*2. Bond SP. FIX. Mode in the user mode: ONSupplement:- The above copy speed does not change

T-1-11

Paper size Single-sided Double-sidedCasette feed Manual feed Casette feed Manual feedPlain paper A422222121A5 25.5 25.5 - -A5R - 9.5 - 9B5 23 23 22.5

*1. Bond SP. FIX. Mode in the user mode: OFF*2. Bond SP. FIX. Mode in the user mode: ONSupplement:- The above copy speed does not change irrespective

T-1-12

Paper size Single-sided Double-sidedCasette feed Manual feed Casette feed Manual feedPlain paper A418181818A5 25.5 25.5 - -A5R - 9.5 - 9B5 23 23 22.5

*1. Bond SP. FIX. Mode in the user mode: OFF*2. Bond SP. FIX. Mode in the user mode: ONSupplement:- The above copy speed does not change irrespective

Chapter 2 Installation

ContentsContentsChapter 1 Introduction1.1 System Construction ...

ContentsContents2.1 Making Pre-Checks...

Chapter 22-12.1 Making Pre-Checks2.1.1 Selecting the Site of Installation0017-5507iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iSelect the sit

Chapter 2 2-22) The machine weighs a maximum of about 53 kg. Be sure to work in a group of 2 persons when lifting it.1-2 Checking the ContentsCheck t

Chapter 22-31-3 Names of PartsF-2-4 *2. iR2022i only[1] DADF [10] Left door[2] Reader front cover [11] Left cover (rear)[3] Control panel [12] Reade

Chapter 2 2-42.1.3 Before Starting the Work (230V CENV)0017-7151iR2025 / iR20301-1 Points to Make Before InstallationBe sure to go through the follow

Chapter 22-5[3] Control panel [12] Reader left cover[4] Delivery tray [13] Reader right cover[5] Front cover [14] Reader erar cover[6] Cassette 1 [15]

Chapter 2 2-62.2 Unpacking and Installation2.2.1 Unpacking and Removing the Packaging Materials0017-5523iR2025 / iR2030 / iR2018 / iR20221) Unpack t

Chapter 22-72) Turn the developer pressure release lever [1] clockwise, and then open theleft door [2] until it stops.F-2-103) Open the packaging bag

Contents1.2.7 Function List...

Chapter 2 2-89) Close the front cover [1].F-2-172.2.4 Installing the Toner Bottle0017-5526iR2018 / iR20221) Shake the toner bottle 5-6 times.F-2-182

Chapter 22-92.2.5 Installing the Toner Bottle0017-5527iR2022i / iR2025 / iR2030 / iR2018i1) Shake the toner bottle 5-6 times.F-2-242) Open the front c

Chapter 2 2-102.2.6 Setting the Cassettes0017-5528iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Holding the knob [1] at the center of the

Chapter 22-117) Affix the cassette size label [1] to the paper size indication plate [2].F-2-368) Affix the caution sheet printed in an appropriate la

Chapter 2 2-124) Using or , select the country/region type that conforms to the com-munication standard used in the country/region where the machi

Chapter 22-132.2.12 Setting the Date and Time0017-5535iR2022i / iR2025 / iR2030 / iR2018i1) Press key to display the user mode screen. 2) Select &qu

Chapter 2 2-142.2.13 Attaching Other Parts0017-5536iR2022i / iR2018ia. Finger pinch caution label1) Open the DADF and affix the supplied finger pinch

Chapter 22-152.3 Checking the Connection to the Network2.3.1 Checking the Network Connection0017-5537iR2018 / iR2022If the machine supports a network

Chapter 2 2-162.3.2 Checking the Network Connection0017-5539iR2022i / iR2025 / iR2030 / iR2018iIf the machine supports a network feature, check the n

Chapter 22-172.4 Flow of Accessory Installation2.4.1 Flow of Accessary Installation (230V CENV)0017-7884iR2022i / iR2018iIf you are going to install a

ContentsChapter 3 Main Controller3.1 Construction ...

Chapter 2 2-182.4.2 Flow of Accessary Installation (230V CENV)0017-7885iR2025 / iR2030If you are going to install any accessory after installing the

Chapter 22-192.5 Installing the Card Reader2.5.1 Points to Note0017-5544iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i2.5.2 Checking the Conte

Chapter 2 2-20<Card reader attachment-D1>F-2-47[1]Card reader mount 1 pc.[2]Card reader cover 1 pc.[3]Harness cover (base + lid) 3 pcs.[4] Repe

Chapter 22-212.5.3 Installation Procedure0017-5546iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i1) Turn off the main power switch [1] of the h

Chapter 2 2-22F-2-525) Insert the card reader [2] harness and ground cable into the hole in the supplied card reader mount [1]. Using the screw [3] r

Chapter 22-238) Connect the connector [1] of the supplied repeating harness B to the connector [2] on the card reader. 9) Secure the repeating harness

Chapter 2 2-2413) Attach the card reader to the reader.- Supplied TP screws (M4x16) [1], 2 pcs.F-2-5814) Slide the card reader cover [1] to attach it

Chapter 22-2516) Affix the two supplied harness covers (bases) at the right rear of the machine with it aligned with the bottom line of the reader.F-2

Chapter 2 2-2620) Using the three harness covers (lids) [2], secure the repeating harness B [1] to the harness covers (bases).F-2-6621) Using a nippe

Chapter 22-271) Plug the power cord [1] into the outlet, and then turn on the main power switch [2].F-2-692) Press the following keys to display the s