Canon PIXMA MP130 Wartungshandbuch

PIXMA MP110/130 SERVICE MANUAL REVISION 0 HY8-13A2-000 COPYRIGHT©2004 CANON INC. CANON PIXMAMP110/130 NOVEMBER

1-4 1-5 Serial Number Label Location The middle on the rear cover

1-5 2. LIST OF ERROR DISPLAY / INDICATION Error Messages Look for the applicable error message and execute the appropriate countermeasures. 2-1 Use

1-6 “CARTRIDGE JAMMED” Printing position compensation failed Cause: Carriage movement prevented by one of the following. Damaged or deformed carriage

1-7 “COLOR INK LOW” Cause: The ink level in the color ink tank is low. Solution: Make sure you have a new color ink tank ready to replace the used one

1-8 2-2 User Error Codes None. 2-3 Service Error Codes None 2-4 New Error Code and Recovery Methods None 2-5 Warnings Main body no LED indications.

1-9 2-6 Troubleshooting by symptom Symptom Solution Remarks The unit does not power on. (1) Check the power cord connection. (2) Check the connec

1-10 Symptom Solution Remarks Blotches or blank ink appears after cleaning the print head. Lines that the printing data does not contain are print

1-11 board after the replacement. *2 Replace the print head only when the machine does not recover after refreshing the print head twice. Missing do

1-12 3. REPAIR 3-1 Notes on Service Part Replacement (and Disassembling / Reassembling) Service part Notes on replacement*1 Adjustment / settings Op

1-13 Service part Notes on replacement*1 Adjustment / settings*2 Operation check TIMING SLIT STRIP FILM (HY7-2821) TIMING SLIT DISK FILM (HY7-281

Scope This manual has been issued by Canon Inc., to provide the service technicians of this product with the information necessary for qualified pers

1-14 3-2 Special Notes on Repair Servicing (1) Flexible cable and harness wiring, connection Be careful of wiring of the flexible cables and harness.

1-15 Each of the front right cover or the front left cover has 4 claws. Since the claws of A are located back of the paper feed section, remove the co

1-16 3-3. Adjustment / Settings (1) Paper feed motor adjustment The following adjustment is necessary when installing the paper feed motor unit. 1)

1-17 (2) Grease application 1 (Rear Side) 3 (Rear Side) 2 4, 5 6 7 10 12 8 9 11 (Bottom Surface)

1-18 Parts to be applied Locations Grease/Oil Type Amount 1 CARRIAGE UNIT Sliding Portion (back surface) FLOIL KG107 60 - 140 mg PRINTE

1-19 3-4 User Data Flowchart 212% 4"x6" -> LTR 25% MIN. 95% A4 -> LTR*100% 170% 5"x7" -> LTR Press the COPY button,

1-20 *: Refer to the Copy Mode Menu. 4.PRINT DATE ON OFF SINGLE IMG SEL RANGE LTR 4"x6" 5"x7" HIGH RES. PH PRO OTHER Press the

1-21 3-5 Service Switches (1) Hardware Switches There is no service hardware switch on the Circuit board. (2) Service Data Overview Service data can

1-22 (3) Service Data Registration/ Setting Method Service data can be registered/set by the following operations: 100% NORMAL STANDBY(Copy mode)LT

1-23 (4) Service Data Menu Service menuSERVICE MENUFIRMWARE: xx.xxSERVICE MENULANG. SELECT?-+SERVICE MENUCARD PROTECT?SERVICE MENUMARKET MODEL?-+SERVI

I. MANUAL OUTLINE This manual consists of the following three parts to provide information necessary to service the PIXMA MP110/MP130: Part 1: Maint

1-24 (5) New SSSWs/Parameters Added to This Model No SSSWs/parameters are newly added to this model.

1-25 3-6 DIAGNOSTIC MENU (hereinafter referred to as Test Mode) (1) User Test Print Functions User enabled Test print functions are as follow. Nozzle

1-26 (3) Test Mode Menu This machine is equipped with the test mode to check operations of various functions listed below. Please refer to Service Dat

1-27 a) PANEL Test If you select test menu in the TEST mode, PANEL test is displayed. To select the test menu, press the OK button. In this test, chec

1-28 Press the OK buttonPress the OK buttonPress the OK buttonPress the OK buttonPress the OK buttonPress the OK buttonPress the Stop/Reset key to end

1-29 3-7 Upgrading the version of flash ROM To upgrade the version of flash ROM, always down load via USB interface. <Flash ROM upgrading file>

1-30 4. Cleaning Your Machine 4-1 Exterior Main Unit Outer Covers Dampen a soft cloth with water or a neutral detergent diluted with enough water, an

1-31 5. Shipping the Main Unit If you must ship the machine as after making repairs, be sure to go through the following: 1) See to it that the B

Part 2 Technical Reference

2 - 1 1. NEW TECHNOLOGIES No new technologies are newly added to this model. 2. CLEANING MODE AND AMOUNT OF INK PURGED To prevent printing problems d

II. TABLE OF CONTENTS Page Part 1: MAINTENANCE 1-1 1. MAINTENANCE 1-1 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Repla

2 - 2 3. Print Mode (1) Copy Paper type Custom setting value in driver UI High speed 5 <- 4 3 -> 2 High quality 1 Plain paper (Color) Print

2 - 3 (3) Standard Color Printing (at PC Printer Driver) Blue character: Default setting Yellow frames: Selectable, even if Custom is not selected in

2 - 4 (4) Standard Gray Scale Printing (at PC Printer Driver) Blue character: Default setting Yellow frames: Selectable, even if Custom is not selec

2 - 5 (5) Borderless Printing (at PC Printer Driver) Blue character: Default setting Yellow frames: Selectable, even if Custom is not selected in the

2 - 6 4. FAQ Problem specific to the MP110/MP130 and corrective actions No. * Function Phenomenon Possible Call / Claim Corrective action Cau

2 - 7 8 B Smearing on printed side. - Smear on the printed side of paper - Cannot print properly - Paper edge crease 1. Correct the paper curl. 2.

Part 3 Appendix

3 - 1 1. Wiring Diagram Paper FeedMotorPower SupplyUnitScaner UnitFlatCableFlatCableFlatCableOperation PanelCarriage UnitCover SensorPick-UpSensorPa

3 - 2 PIXMA MP110/MP130 Specification <General> Printer YES Scanner YES Copy YES Facsimile NO Memory Card YES Media CF (Type I/II) Mic

3 - 3 <Scanner Function> Type Flatbet Reading System Sensor Type Contact Image Sensor ADF NO Reading Resolution Optical resolution 1200 x 2

Page Part 2: TECHNICAL REFERENCE 2-1 1. NEW TECHNOLOGIES 2-1 2. CLEANING MODE AND AMOUNT OF INK PURGED 2-2 3. PRINT MODE 2-6 4. FAQ (Pr

3 - 4 <Copy Function> Copy Print Resolution Black & White 600 dpi Color 1200 dpi Copy speed Black & White (Draft) 16 ppm Color (F

PRINTED IN JAPAN (IMPRIME AU JAPON) CANON INC.

Part 1 Maintenance

1-1 1. MAINTENANCE 1-1 Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer (1) Adjustment I

1-2 (3) Periodic replacement parts Item Timing Purpose Tool Approx. time None (4) Replacement consumables Item Timing Purpose Tool Approx.

1-3 1-3 Product Life (1) Main body At any of the following (I) to (II), whichever comes first. (I) Print Volume: 4,000 pages BK: 2,000 pages (in print