Canon PIXMA MG6440 Bedienungsanleitung

MG6400 seriesOnline ManualTroubleshooting English

The Machine Stopped Working SuddenlyCannot Communicate with the Machine over the Wireless LANCannot Print, Scan, or Access the Card Slot from a Comput

• A000 to ZZZZB200 C000 About the support code for paper jam, you can also refer to Support Code List (When Paper Is Jammed).100

Support Code List (When Paper Is Jammed)If the paper is jammed, remove it following the procedure appropriate for each case.• If you can see the jamme

1300CausePaper is jammed in the paper output slot.ActionIf you can see the jammed paper at the paper output slot, remove the paper following the proce

If you cannot remove the paper or the paper tears inside the machine, or if the paper jam error continuesafter removing the paper, contact the service

1303CausePaper is jammed inside the machine at the transport unit.ActionIf you cannot see the paper at the paper output slot, remove the paper from th

Note•If the paper is rolled up and it is difficult to remove, grasp the edges of the paper, then removethe jammed paper.•If you cannot remove the jamm

1304CausePaper is jammed when performing automatic duplex printing.ActionIf the paper is jammed when performing automatic duplex printing, remove the

6.Pull out the jammed paper slowly.When you pull the jammed paper, support the machine with your hand so that it does not fall down.Note• If the paper

8. Plug the machine back in and turn the machine back on.All print jobs in the queue are canceled. Reprint if necessary.If you cannot remove the paper

Paper Is Jammed inside the MachineIf the jammed paper tears and you cannot remove the paper either from the paper output slot or from thetransport uni

If the firewall function of your security software is turned on, a message may appear warning that Canonsoftware is attempting to access the network.

4.Hold the jammed paper with your hands.If the paper is rolled up, pull it out.5.Pull the paper slowly not to tear it, then pull the paper out.Keep an

• Does the piece of paper remain in the right side or the left side space (C) inside the machine?7.Close the operation panel slowly.All print jobs in

In Other CasesMake sure of the following:Check1 Are there any foreign objects around the paper output slot?Check2 Is the paper curled?Load the paper a

1003CauseThe machine is out of paper, or paper does not feed.ActionClose the paper output tray, pull the feeder out, then load the paper.When you load

1200CauseThe operation panel is open.ActionClose the operation panel and wait for a while.Do not close it while you are replacing an ink tank.114

1250CauseThe paper output tray is closed.ActionOpen the paper output tray to resume printing.115

1310CauseThe size of paper may not be compatible with automatic duplex printing.ActionThe sizes of media suitable for auto duplex printing are A4 and

1401CauseThe print head may be damaged.ActionContact the service center.117

1403CauseThe print head may be damaged.ActionContact the service center.118

1405CauseThe print head may be damaged.ActionContact the service center.119

Printing Speed Is SlowCheck1 The machine may be printing out or scanning a large job issued from anothercomputer.Check2 Make sure that the radio statu

1410CauseThe ink tank cannot be recognized.ActionOpen the operation panel and replace the ink tank which lamp is off.120

1411CauseThe ink tank cannot be recognized.ActionOpen the operation panel and replace the ink tank which lamp is off.121

1412CauseThe ink tank cannot be recognized.ActionOpen the operation panel and replace the ink tank which lamp is off.122

1413CauseThe ink tank cannot be recognized.ActionOpen the operation panel and replace the ink tank which lamp is off.123

1414CauseThe ink tank cannot be recognized.ActionOpen the operation panel and replace the ink tank which lamp is off.124

1600CauseIf the lamp on the ink tank is flashing, ink may have run out.ActionReplacing the ink tank is recommended.If printing is in progress and you

1660CauseThe ink tank is not installed.ActionInstall the ink tank.126

1680CauseSome ink tanks are not installed in the correct position. (The lamp on the ink tank flashes.)ActionConfirm that the ink tanks are installed i

1681CauseMore than one ink tanks of the same color are installed. (The lamp on the ink tank flashes.)ActionConfirm that the ink tanks are installed in

1684CauseThe ink tank cannot be recognized.ActionPrinting cannot be executed because the ink tank may not be installed properly or may not be compatib

Cannot Use the Card Slot via NetworkCannot Use the Card Slot13

1688CauseThe ink has run out. (The lamp on the ink tank flashes.)ActionReplace the ink tank and close the operation panel.Printing under the current c

1689CausePrinter detected ink out condition (The lamp on the ink tank flashes).ActionReplace the ink tank and close the operation panel.An ink tank th

1700CauseThe ink absorber is almost full.ActionPress the machine's OK button to continue printing. Contact the service center.132

1701CauseThe ink absorber is almost full.ActionPress the machine's OK button to continue printing. Contact the service center.133

1712CauseThe ink absorber is almost full.ActionPress the machine's OK button to continue printing. Contact the service center.134

1713CauseThe ink absorber is almost full.ActionPress the machine's OK button to continue printing. Contact the service center.135

1714CauseThe ink absorber is almost full.ActionPress the machine's OK button to continue printing. Contact the service center.136

1715CauseThe ink absorber is almost full.ActionPress the machine's OK button to continue printing. Contact the service center.137

1890CauseThe protective material for the print head holder or the tape may remain attached to the holder.ActionOpen the operation panel, then confirm

2100CausePaper larger than the paper size in the print settings is loaded.ActionCheck the size of the loaded paper, then press the machine's OK b

Cannot Use the Card SlotCheck1 Is the icon of the card slot displayed?To use the card slot over network, you have to mount the card slot as the networ

2101CausePaper smaller than the paper size in the print settings is loaded.ActionCheck the size of the loaded paper, then press the machine's OK

2102CauseThe machine has detected that the paper has been fed aligned to one side.ActionClose the paper output tray, then pull the feeder out.Load the

2103CauseThe machine cannot detect the paper size.ActionPress the machine's Stop button to dismiss the error, then try to print again.If this err

2700CauseSome errors occurred while copying and a certain time passed.ActionPress the OK button to dismiss the error, and try to copy again.143

2900CauseScanning the print head alignment sheet has failed.ActionPress the OK button to dismiss the error, then take the actions described below.• Ma

4100CauseThe specified data cannot be printed.ActionWhen you print the contents on CREATIVE PARK PREMIUM, confirm the message on the computerscreen, m

4103CauseCannot perform automatic duplex printing with the current paper size setting.ActionPress the machine's Stop button, to cancel printing.T

5011CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

5012CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

5100CausePrinter error has occurred.ActionCancel printing, and turn off the machine. Then clear the jammed paper or protective material that isprevent

Cannot Use the Machine on Replacing an Access Point orChanging Its settingsWhen you replace an access point, perform network setup of the machine agai

5200CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

5400CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

5B00CausePrinter error has occurred.ActionContact the service center.152

5B01CausePrinter error has occurred.ActionContact the service center.153

5B12CausePrinter error has occurred.ActionContact the service center.154

5B13CausePrinter error has occurred.ActionContact the service center.155

5B14CausePrinter error has occurred.ActionContact the service center.156

5B15CausePrinter error has occurred.ActionContact the service center.157

6000CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6500CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

Cannot Detect a Machine on a NetworkCannot Detect the Machine When Setting up Network CommunicationThe Machine Cannot Be Detected in the Wireless LAN1

6502CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6800CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6801CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6900CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6901CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6902CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6910CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6911CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6930CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6931CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

Cannot Detect the Machine When Setting up NetworkCommunicationIf the machine could not be detected on the network when setting up the network communic

6932CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6933CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6934CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6935CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6936CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6937CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6938CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6940CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6941CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6942CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

Cannot Detect the Machine during Wireless LAN Setup: Check 1Are the machine and network device (router, access point, etc.) turned on?Make sure that t

6943CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6944CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6945CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

6946CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

B200CauseAn error requiring you to contact the service center has occurred.ActionTurn off the machine, and unplug the power cord of the machine from t

C000CausePrinter error has occurred.ActionTurn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back i

Cannot Detect the Machine during Wireless LAN Setup: Check 2Is the wireless LAN setting of the machine enabled?Make sure that the Wi-Fi lamp of the ma

ContentsTroubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Problems with Network C

Cannot Detect the Machine during Wireless LAN Setup: Check 3Is the machine connected to the access point?By using the operation panel of the machine,

Cannot Detect the Machine during Wireless LAN Setup: Check 4Are the SSID of the access point connected to your computer and that ofthe machine the sam

Cannot Detect the Machine during Wireless LAN Setup: Check 5Does the firewall function of your security software or operation system forcomputer inter

Cannot Detect the Machine during Wireless LAN Setup: Check 6Check the settings of the access point.Check the settings of the access point for the netw

The Machine Cannot Be Detected in the Wireless LANCheck1 Make sure that the machine is turned on.Check2 Is WLAN active/inactive in LAN settings under

Check12 When using a router, connect the printer and computer to the LAN side (samenetwork segment).Check13 When the printer is connected to an AirPor

Other Problems with NetworkForgot an Access Point Name, SSID, or a Network KeyThe Message Is Displayed on the Computer Screen During SetupThe Admin Pa

Forgot an Access Point Name, SSID, or a Network KeyCannot Connect with an Access Point to Which a WEP/WPA/WPA2 Key Is Set (You Forgot theWEP/WPA/WPA2

Select either TKIP (Basic Encryption) or AES (Secure Encryption) for the dynamic encryptionmethod.For details, see Changing the WPA or WPA2 Detailed S

The Message Is Displayed on the Computer Screen During SetupThe Enter Password Screen Is Displayed During SetupThe Screen for Setting the Encryption I

Paper Is Smudged/Printed Surface Is Scratched. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Back of the Paper Is Smud

The Admin Password Set to the Machine Was ForgottenInitialize the LAN settings.How to Restore the Machine's Network Settings to Factory DefaultAf

Checking Information about the NetworkChecking the IP Address or the MAC Address of the MachineChecking the IP Address or the MAC Address of the Compu

1. Open the Utilities folder in the Applications folder.2. Start Network Utility.3. Click the Ping button.4.Make sure that Send only XX pings (XX are

How to Restore the Machine's Network Settings to Factory DefaultImportant• Note that initialization erases all network settings on the machine, a

Problems with PrintingPrinting Does Not StartPaper JamsPaper Does Not Feed Properly/"No Paper" Error OccursCannot Print Properly with Automa

Printing Does Not StartCheck1 Make sure that the power plug is securely plugged in, then press the ON buttonto turn the machine on.While the POWER lam

Paper JamsWhen paper is jammed, a troubleshooting message is displayed automatically. Take the appropriate actiondescribed in the message.• When a Sup

Paper Does Not Feed Properly/"No Paper" Error OccursCheck1 Make sure that paper is loaded.Loading PaperCheck2 Make sure of the following whe

If multiple sheets of plain paper is fed from the machine, select the setting for preventing double-feed of plainpaper using the operation panel or yo

Cannot Print Properly with Automatic Duplex PrintingCheck1 Is the setting for automatic duplex printing selected?Make sure that the Two-Sided check bo

If an Error Occurs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Copying/Printing Stops Before It Is CompletedCheck1 Is the paper loaded?Make sure that paper is loaded.If the machine has run out of paper, load paper

Problems with Printing QualityPrint Results Not SatisfactoryInk Is Not Ejected41

Print Results Not SatisfactoryIf the print result is not satisfactory due to white streaks, misaligned lines, or uneven colors, confirm thepaper and p

See also the sections below:Cannot Print to End of JobNo Printing Results/Printing Is Blurred/Colors Are Wrong/White StreaksLines Are MisalignedPrinte

Cannot Print to End of JobCheck Is the space of your computer's hard disk sufficient?Delete unnecessary files to free disk space.44

No Printing Results/Printing Is Blurred/Colors Are Wrong/WhiteStreaks No Printing Results Printing Is Blurred Colors Are Wrong White Streaks45

Check1 Did you confirm the paper and print quality settings?Print Results Not SatisfactoryCheck2 Check the status of ink tanks. Replace the ink tank i

Check6 Is the platen glass dirty?Clean the platen glass.Cleaning the Platen Glass and Document CoverCheck7 Make sure that the original is properly loa

Lines Are MisalignedCheck1 Did you confirm the paper and print quality settings?Print Results Not SatisfactoryCheck2 Perform Print Head Alignment.If p

Printed Paper Curls or Has Ink Blots Printed Paper Has Ink Blots Printed Paper CurlsCheck1 Did you confirm the paper and print quality settings?Print

1715. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1371890. . . .

Paper Is Smudged/Printed Surface Is Scratched Paper Is SmudgedThe Edges of Paper Are Smudged Printed Surface Is Smudged Printed Surface Is ScratchedCh

1. Roll up the paper in the opposite direction to the paper curl as shown below.2. Check that the paper is now flat.We recommend printing curl-correct

If you are using plain paper to print images with high intensity, the paper may absorb too much ink and becomewavy, causing paper abrasion.• When prin

4. Drag the Ink Drying Wait Time: slide bar to set the wait time, and then click Apply.5. Confirm the message and click OK.53

Back of the Paper Is SmudgedCheck1 Did you confirm the paper and print quality settings?Print Results Not SatisfactoryCheck2 Perform the Bottom Plate

Vertical Lines Are Printed on the Sides of the PrintoutCheck Is the size of the loaded paper correct?The vertical lines may be printed in the margin i

Colors Are Uneven or Streaked Colors Are Uneven Colors Are StreakedCheck1 Did you confirm the paper and print quality settings?Print Results Not Satis

If Print Head Deep Cleaning does not resolve the problem, the print head may be damaged. Contact theservice center.Check3 Perform Print Head Alignment

Ink Is Not EjectedCheck1 Has the ink run out?Check the Support Code on the LCD and take the appropriate action to resolve the error.Support Code ListC

Problems with ScanningProblems with ScanningScan Results Not Satisfactory59

6933. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1716934. . . .

Problems with ScanningScanner Does Not WorkScanner Driver Does Not StartError Message Appears and the Scanner Driver Screen Does Not AppearCannot Scan

Scanner Does Not WorkCheck 1: Make sure that your scanner or printer is turned on.Check 2: Connect the USB cable to a different USB port on thecompute

Scanner Driver Does Not StartCheck 1: Make sure that the scanner driver is installed.If not installed, install the scanner driver from the web page.Ch

Error Message Appears and the Scanner Driver ScreenDoes Not AppearCheck 1: Make sure that your scanner or printer is turned on.Check 2: Turn off your

Cannot Scan Multiple Items at One TimeCheck 1: Make sure that the items are placed correctly.Placing Items (When Scanning from a Computer)Check 2: Che

Cannot Scan Properly with Auto ScanCheck 1: Make sure that the items are placed correctly.Placing Items (When Scanning from a Computer)Check 2: Multip

Slow Scanning SpeedCheck 1: To view the image on a monitor, set the outputresolution to around 150 dpi. To print, set it to around 300 dpi.ResolutionC

"There is not enough memory." Message Is DisplayedCheck 1: Exit other applications and try again.Check 2: Reduce the resolution or output si

Computer Stops Operating during ScanningCheck 1: Restart the computer, reduce the output resolutionand scan again.ResolutionCheck 2: Delete unnecessar

Scanned Image Does Not OpenCheck: If the data format is not supported by the application,scan the image again and select a popular data format such as

TroubleshootingThe Machine Cannot Be Powered OnPrinting Does Not StartPaper Does Not Feed Properly/"No Paper" Error OccursPrint Results Not

Scan Results Not SatisfactoryScan Quality (Image Displayed on the Monitor) Is PoorScanned Image Is Surrounded by Extra White AreasCannot Scan at the C

Scan Quality (Image Displayed on the Monitor) Is PoorCheck 1: Increase the scanning resolution if the image isjagged.ResolutionCheck 2: Set the displa

Refer to "Image Corrections and Color Adjustments" for details.72

Scanned Image Is Surrounded by Extra White AreasCheck: Specify the scan area.You can also manually specify the scan area in thumbnail view or when the

Cannot Scan at the Correct SizeCheck: Make sure that the items are placed correctly.Placing Items (When Scanning from a Computer)74

Position or Size of the Image Cannot be DetectedCorrectly When Scanning from the Operation PanelCheck 1: Make sure that the items are placed correctly

Item Is Placed Correctly, but the Scanned Image IsSlantedCheck: When Document or Magazine is selected for the itemtype, deselect the Correct slanted t

Scanned Image Is Enlarged (Reduced) on the ComputerMonitorCheck 1: Change the display setting in the application.Refer to the application's manua

Problems with the MachineThe Machine Cannot Be Powered OnThe Machine Turns Off UnintendedlyCannot Connect to Computer with a USB Cable ProperlyCannot

The Machine Cannot Be Powered OnCheck1 Press the ON button.Check2 Make sure that the power plug is securely plugged into the power cordconnector of th

Problems with Network CommunicationProblems with the Machine While Using with NetworkCannot Detect a Machine on a NetworkOther Problems with Network8

The Machine Turns Off UnintendedlyCheck Deactivate the setting to turn the unit off automatically.The machine turns off automatically according to the

Cannot Connect to Computer with a USB Cable ProperlyPrinting or Scanning Speed Is Slow/Hi-Speed USB Connection Does NotWorkIf your system environment

Cannot Communicate with the Machine with USB ConnectionCheck1 Make sure that the machine is turned on.Check2 Make sure that the USB cable is connected

LCD Cannot Be Seen At All• If the POWER lamp is off:The machine is not powered on. Connect the power cord and press the ON button.• If the POWER lamp

An Unintended Language Is Displayed on the LCDSelect the language you want to be displayed according to the following procedure.1. Press the HOME butt

Cannot Remove a Memory CardContact the service center.Important• Never attempt to remove a memory card using a thin stick or tweezers. Doing so may da

Print Head Holder Does Not Move to the Position for ReplacingCheck1 Is the POWER lamp off?Check if the POWER lamp is lit.The print head holder will no

Problems with Installation/DownloadingCannot Install the MP DriversUninstalling IJ Network Tool87

Cannot Install the MP DriversReinstall the MP Drivers.When you reinstall the MP Drivers, install the MP Drivers from our website.88

Uninstalling IJ Network ToolFollow the procedure below to uninstall IJ Network Tool from your computer.Important• Even if IJ Network Tool is uninstall

Problems with the Machine While Using with NetworkThe Machine Stopped Working SuddenlyPrinting Speed Is SlowCannot Use the Card Slot via NetworkCannot

About Errors/Messages DisplayedIf an Error OccursA Message Is DisplayedError Message Appears on a PictBridge (Wireless LAN) Compliant Device90

If an Error OccursWhen an error occurs in printing such as the machine is out of paper or paper is jammed, a troubleshootingmessage is displayed autom

A Message Is DisplayedThis section describes some of the errors or messages.Note• A Support Code (error number) is displayed on the computer or on the

• The card is currently writable from PC. Set to [Not writable from PC].The card slot is set to Writable from USB PC or Writable from LAN PC.You canno

• If you agree to participate in the survey program:Click Agree, then follow the on-screen instructions. The printer usage information will be sent vi

4. Restart the computer.Empty the Trash and restart your computer.• Changing the setting:To display the confirmation screen every time the printer usa

Error Message Appears on a PictBridge (Wireless LAN) CompliantDeviceThe following are the possible errors that may occur when printing directly from a

• The ink tank is not compatible with this machine.Printing cannot be executed because the ink tank is not compatible with this machine.Install an app

If You Cannot Resolve the ProblemIf you cannot resolve the problem with any of the workarounds in this chapter, please contact the seller ofthe machin

Support Code List(MG6410, MG6420, MG6440, MG6450, MG6460, MG6470, MG6480)The support code appears on the LCD and the computer screen when an error occ