EN-1FCC NoticeThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. Th
EN-104. Insert the plug from the AC adapter into the DC IN terminal.5. Insert the appropriate end of the power cord into the AC adapter.6. Insert the
EN-11Remote controlFor the first time use:Remove the transparent insulation tape by pulling it beforeuse.For battery change:1. Push the catch to the r
EN-122. Remove the old Lithium coin cell and install new one (CR2025).Ensure that the side with the mark “+” is up.3. Push the battery holder back int
EN-13CAUTION:Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type recommended by the manufacturer.Disp
EN-14InstallationLayout of the projectorImage size varies depending on the distance between the screen and the projector.Front projectionLWABHCDL : Be
EN-15Caution:Do not place the projector on a carpet or any flammable materials. It may causedamage or fire.Place the projector at least 10 cm (or 4 in
EN-16VIDEO INS-VIDEO INto S-video outputto video outputVCR etc.AUDIO INAUDIO OUTto Audio outputBasic connectionsThis projector can be connected with v
EN-17Projector + ComputerFor computer with D-SUBImportant:When you use a longer RGB cable instead of the common length cable, the imagemay not be proj
EN-18PreparationPreparation for projection1. Attach the provided AC adapter to the projector.2. Plug the AC adapter in the wall outlet.The POWER indic
EN-19In the following cases:Important:When the keystone adjustment is carried out, the adjustment value is indicated. Notethat this value doesn’t mean
EN-2ContentsImportant safeguards...3Overview...
EN-20Basic operationOn the control panel433Power-on1. Turn on the device connected to the projector first.2. Plug the AC adapter in both the projector
EN-21Important:Images may not be projected with good quality in an extremely hot or cold environment.(This is not a product malfunction.)4. Adjust the
EN-22On the remote controlKeystone S T buttonPress the Keystone S or KeystoneT to adjust image distortion caused by tilting the projector.Important:Ke
EN-23*1: Not active when connecting with VGA signal and SD card mode.*2: Active when connecting with VGA, Component_P and HD source.*3: Active when co
EN-241 ColorBrightness...Use to adjust the image brightness. The image becomes brighter asthe value increases.Contrast...Use
EN-253. ManagementProjection Ceiling... Use to reverse the image horizontally.Project Rear... Use to reverse the image vertica
EN-26Using an SD CardYou can playback image and video files stored in an SD card.VideoMPEG1Supported file type: *.mpg(I-FrameSupported audio format: M
EN-27Still Image JPEGSupported file type: *.jpg (up to 16M pixels)Supported Supported model namebrand nameCanon PowerShot G1
EN-28Inserting/Removing an SD Card1. Insert the SD card in the correct orientation shown.2. To removing an SD card, press lightly on the edgeof the SD
EN-29TroubleshootingThe following offers solutions to some of the common problems you may encounter. Wesuggest that you consult this chart before cont
EN-3Important safeguardsPlease read all these instructions regarding your projector and retain them for futurereference. Follow all warnings and instr
EN-30Turn on the power of the connected device, or check whetherthere is something wrong with the connected device.Check the external device outputs s
EN-31OthersProblem Cause and solutionProjected images appear wavyand distorted.Tint in projected images isincorrect.Projected images areobscured.Fine
EN-32This air comes out as a result of cooling the inside ofthe projector. This isn’t a product malfunction.The microcomputers inside the projector ma
EN-33MaintenanceCaution:Be sure to turn off the lamp and unplug the power cord from the wall outlet before youperform any maintenance on the projector
EN-34 POWER (Red)OFFONCHARGE (Red)OFFOFFCONDITIONSystem ONSystem standby POWER (Red)OFFOFFONONCHARGE (Red)ONOFFONOFF CONDITIONSystem ON+Battery chargi
EN-35Normal condition (Battery only)Abnormal condition POWER (Red)OFFONFlashing x 10CHARGE (Red)OFFOFFOFFCONDITIONSystem ONSystem standbyLow Battery
EN-36SpecificationsType DLPTM projectorRated input 15V, 2.0ADisplay technology Single 0.55” DLP panelNative resolution 800 x 600 pixelsColors 16.7 mil
EN-37Dimensional drawings (unit : mm)
EN-38What’s included in the box1 Soft Carrying Bag (for projector only)1 User’s Manual1 Quick Start Guide1 Composite Video Cable1 AC Adaptor1 Power Co
EN-39Signal mode Resolution (H x V) Horizontal frequency (kHz) Vertical frequency (Hz)VGA 60 640 x 350 31.47 59.94VGA 85 640 x 350 37.86 85.08V
EN-49. VentilationSlots and openings in the cabinet are provided for ventilation, ensuring reliable operationof the projector and to protect it from o
EN-40Important:Some computers aren’t compatible with the projector.The projector’s maximum resolution is 800 x 600 pixels. It may not display images o
EN-5(a) If the power-supply cord or plug is damaged.(b) If the adaptor or the battery is damaged.(c) If liquid has been spilled, or objects have falle
EN-6WARNING:Unplug the power cord or remove the battery immediately if there is somethingwrong with your projector.Do not operate if smoke, strange no
EN-7Do not unplug the power cord or remove the battery during operation.It can lead to lamp breakage, fire, electric shock or other trouble. Wait for
EN-8Overview125648739Control panel 1 LAMP indicator 2 POWER indicator 3 CHARGE indicator 4 POWER button 5 Four directionalbuttons 6 OK button 7 MENU
EN-9PowerUsing the provided AC adapter or an optional Lithium-ion rechargeable battery.Warning:The projector must be used with the provided AC adapter
Kommentare zu diesen Handbüchern