Canon SX 50 Bedienungsanleitung PDF herunterladen (Seite 233)

Projector User Commands

- 227 -

Revision Histor

/ Date Chan

es Revised b

roved b

10. Error List

Errors supported

by model

Item Code TYPE Error character strings

(1) (2) (3) (4)

Error Remedy

1 0001 e BAD_SEQUENCE O O O O Communication sequence error.

Wait until a response is received before

sending the next command.

2 0002 e INVALID_COMMAND O O O O Invalid (undefined) command. Send a valid command.

3 0003 e INVALID_MODE O O O O

The designated command cannot be

executed in this mode.

Switch the mode using the REMOTE or

LOCAL command.

4 0004 e INVALID_FORMAT O O O O Invalid command format. Send the command in the valid format.

5 0005 e NOT_POWER_SUPPLIED O O O O The projector's power is off.

Turn on the power using the POWER ON

command.

6 - i BUSY O O O O

Mode switching or processing inside the

projector is underway.

Wait until the power supply state

changes to ON, OFF or PMM.

7 000A e INVALID_PARAMETER O O O O

The parameter (type) is invalid

(undefined).This includes the case when

the number of parameters is incorrect.

Use the correct parameter(s).

8 000B e JOB_TIMEOUT O O O O

Internal processing of the projector has

timed out.

Resend the command.

9 - w

USER_COMMAND_VERSION_

IS_UPDATED

O O O O

The user command version is being

updated.

Use GET COMVER to obtain the latest

user command version.

i BUSY (FOCUS) O O O The focus lens is now being driven. Wait until the focus lens drive stops.

10 -

i BUSY (ZOOM) O O O The zoom lens is now being driven. Wait until the zoom lens drive stops.

F001 e SYSTEM (UNKNOWN) O O O O An internal error occurred. Resend the command.

F002 e SYSTEM (FOCUS) O O O

An error occurred in

AUTOSETEXE=FOCUS.

F004 e SYSTEM (AUTO_KEYSTONE) O O O

An error occurred in

AUTOSETEXE=VKS.

F005 e SYSTEM (SCREEN_COLOR) O O O

An error occurred in

AUTOSETEXE=SCRN.

Eliminate the cause of the error, and

resend the command.

12 E0XX e COMMUNICATION_ERROR O O O O

A communication protocol violation

occurred in the projector.

Resend the command.

13 1008 e NOT_SUPPORTED_ASPECT O

Specified aspect cannot be set since the

screen aspect is not 4:3.

Use the range command to obtain an

addressable parameter range to be set

for ASPECT.

14 1008 e INVALID_SCREEN_ASPECT O

It cannot be executed due to current

screen aspect setting.

Change the screen aspect setting.

15 200X e INVALID_SOURCE (****) O O O O

It cannot be executed with the current

input source. Current input source is

shown in brackets.

Change the input source.

2010 e NO_SIGNAL O O O O There is no signal input. Input the signal.

201X e INVALID_SIGNAL O O O O

It cannot be executed with the current

input signal. Current input signal is

shown in brackets.

Change the input signal.

i BUSY (NOW_SETTING) O O O O Signal setting (detection) is in progress.

BUSY

(POWER_MANAGEMENT_RE

ADY)

O O O O

Preparing to switch to power

management standby.

17 -

i BUSY (INTERNAL_PROCESS) O O O O Heavy processing is in progress.

Wait until the processing is completed.

0801

0802

e INVALID_VALUE O O O O

Numerical parameters are invalid or

outside the range.

Use the RANGE command to obtain the

parameter range, and then use a

parameter within the range.

1001 e TERMINAL_OUT O

The input cannot be selected since the

terminal is set to output.

Use the TERMINAL command to set the

terminal to input, and then select the

input again.

1002 e NO_LOGO_CAPTURED O O O

Processing cannot be executed since the

user image is not registered.

1003 e IP_NOT_AVAILABLE O O O O IP conversion cannot be performed. Change to the correct input signal.

1004 e POWER_MANAGEMENT_OFF O O O

DPON cannot be set to ON when PMM is

OFF.

Set DPON to anything other than OFF.

1005 e DIRECT_POWER_ON O O O

PMM cannot be set to OFF when DPON

is ON.

Set DPON to OFF.

1006 e NOW_BLANK O O O

AUTOSETEXE=FOCUS or SCRN

cannot be executed since BLANK is ON.

After setting BLANK to OFF, resend the

command.

203X e INVALID_RESOLUTION (***) O O O O The input signal resolution is not correct.

Change to the correct resolution of the

input signal.

20 - i INPUT_NOT_FOUND O O O

The input was not switched since no

input signal was found with

AUTOSETEXE=INPUT.

There is no action to be taken since the

status has been notified.

1 2 ... 228 229 230 231 232 233 234 235 236 237 238 ... 243 244

Kommentare zu diesen Handbüchern

Keine Kommentare

Canon SX 50 Bedienungsanleitung Seite 233

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Projektoren Canon SX 50